Picoscope 2208B MSO Review

There are few tools that are essential for an electronics hobbyist. When I started, I had a soldering iron, a multimeter and some components, and that was about it. That got me quite far because you can do simple debugging even with a multimeter, but once you start to do any communications, you will either work in the dark or get a signal analyzer, oscilloscope, or both. I reached that point about 9 months into my hobby, and eventually decided to get an entry-level PicoScope from Picotech. You can read the whole story from my PicoScope 2204 review from four years ago.

Long story short, I was extremely happy with my Picoscope, and I’ve been using Picotech’s products ever since in various projects. In the past years, I’ve also been collaborating with Picotech, so I’ve had the chance to use also their higher end models, including the frighteningly powerful 4-channel, 200 MHz, 16 bit PicoScope 5444B, which is really great but maybe even too hefty for my use. So when I was offered the chance to try out Picotech’s latest generation of their entry-level 2000 series published just a month ago, I was immediately in.

Without further ado, let’s get reviewing!

PicoScope 2000 series overview

The new PicoScope 2000 series is divided into roughly two groups of equipment: The entry models 2204 and 2205 range in price from 139€ for the 10 MHz 2-channel 2204A to 419€ 2205A and 2405A which are 25 MHz and have MSO (mixed-signal oscilloscope, i.e. it has 16 channel digital part as well) capability and 4-channels, respectively. Don’t let the low bandwith confuse you, even these models have sampling rates ranging from 100 MS/s to 500 MS/s, so you will get quite a lot of measuring power out of them.

Biggest limitation with 2204 and 2205 models is the buffer size, which ranges from 8 kS to 48 kS, so for longer captures than a few waveforms, only option is the continuous capture over USB which worked at a steady rate of 1 MS/s the last time I used it. So you can do unlimited capturing of signals around 100 kHz, but above that it’s the normal oscilloscope triggering business — that’s the way scopes have always worked from their beginnings, so it gets the job done as well.

  2204 2205 2206 2207 2208
Bandwith 10 MHz 20 MHz 50 MHz 70 MHz 100 MHz
Sample rate 100 MS/s 200 MS/s 500 MS/s 1000 MS/s 1000 MS/s
Resolution * 8 bit 8 bit 8 bit 8 bit 8 bit
Memory 8 kS 16 kS (48 kS w. MSO/4ch) 32 MS 64 MS 128 MS
Price (2015-22-05) 139 € 209 € 319 € 459 € 629 €
Options MSO or 4ch MSO or 4ch MSO or 4ch MSO or 4ch

*) Resolution for repeating signals can be increased to 12 bit with multiple samples
Continue reading Picoscope 2208B MSO Review

Super Simple 50+ kHz Logic Analysis with ATtiny2313 and FTDI Friend

AVR & FTDI logic analyzer

While banging my head against the wall with debugging my PS/2 keyboard thingy, I really wished I had a dedicated logic analyzer (preferably with PS/2 decoder, but even raw binary data would’ve been fine). So I decided to try out a long hatched idea – combine an ATtiny2313 and FTDI for some unlimited-length logic capturing with a PC. You’ll only need:

  1. ATtiny2313
  2. 20 MHz crystal and caps (slower will also work, frequency just defines what baud rates you’ll achieve)
  3. FTDI USB/serial converter, like the FTDI friend from Adafruit
  4. Optionally, some power-stabilizing capacitors, reset pullup and ISP programming header for flashing the firmware

ATtiny2313 is ideal for this, as it has all eight port B pins on one side in numerical order – attaching up to 8 logic lines is really straightforward. With 20 MHz crystal, baud rates close to 1 Mbps can be achieved in fast serial mode. I used Adafruit’s FTDI Friend for really simple (and way faster than most cheap serial adapter dongles) serial to USB conversion – just connect ATtiny RXD pin to TX, and TXD to RX, and you can even get power from the Friend so you’re all set! For crystal and that other stuff, see my ATtiny2313 breadboard header post for schematic, the picture above should fill you in with the rest.

Firmware code

This device has some of the smallest firmware codebases ever (firmware is 128 bytes). All we need to do is to set up UART with desired speed, and have the AVR chip to fire up an interrupt whenever data has been sent, and then use that to send current state of port B (using PINB):

#include <avr/io.h>
#include <avr/interrupt.h>

void USARTInit(unsigned int ubrr_value, uint8_t x2, uint8_t stopbits) { 
  // Set baud rate
  UBRRL = ubrr_value & 255; 
  UBRRH = ubrr_value >> 8;

  // Frame Format: asynchronous, 8 data bits, no parity, 1/2 stop bits
  UCSRC = _BV(UCSZ1) | _BV(UCSZ0);
  if(stopbits == 2) UCSRC |= _BV(USBS);

  if(x2) UCSRA = _BV(U2X); // 2x

  // USART Data Register Empty Interrupt Enable
  UCSRB = _BV(UDRIE);

  // Enable The receiver and transmitter
  UCSRB |= _BV(RXEN) | _BV(TXEN);
}

int main() {
  // 230.4 kbps, 8 data bits, no parity, 2 stop bits
  USARTInit(10, 1, 2); // replace 10 with 4 to get 0.5 Mbps

  sei(); // enable interrupts

  while(1) {}
	
  return 1;
}

ISR(USART_UDRE_vect) {
  UDR = PINB;
}

Continue reading Super Simple 50+ kHz Logic Analysis with ATtiny2313 and FTDI Friend

World’s Simplest Logic Analyzer for $5

Today’s post documents my recent hack that may just be the world’s simplest logic analyzer. More accurately, it is a circuit consisting of a 74HC126 quad buffer chip and R-2R resistor network (eleven 330 ohm resistors) that acts as a D/A converter, enabling one to analyze four logic lines with a single channel digital oscilloscope and $5 in parts!

With the circuit described below and an entry level USB scope like the PicoScope 2204, bursts of data can be captured at 10 MSps (million samples per second), and continuous capture rates of 2.5 MSps are possible, the length of the capture only limited by your PC’s memory. This is obviously much better than recently covered Bus Pirate’s 1 MSps for 4 ms!

Even higher throughput can be achieved with better scopes, although the A/D conversion requires several consecutive samples at same logic level, which means that a 100 MHz scope with 200 MSps capture rate should generally be able to analyze logic operating at ~40 MHz speeds. At such speeds, a fast buffer chip and D/A converter is naturally needed as well.

Above you can see an example of SD card traffic analyzed using my circuit – the full capture was 10 million samples which enabled me to capture all the traffic generated by my SD tutorial project without any additional triggering. Read on for details of the hack. A lot of effort has been made to keep the material very accessible and informative to electronics beginners, too. In the end of the article, source code for PicoTech 2000 series is included, and it can easily be adapted for any scope that can transfer captured waveforms to PC (in the simplest form by reading waveforms from a CSV file).

How It Works

Basic idea is to connect 4 logic lines to a D/A converter, that will transform the binary 1/0 values (represented by VCC and GND voltage levels, respectively) into a 16-step analog waveform. Because input lines cannot be directly connected to the R-2R resistor network that is used to do the D/A conversion, a 4-line buffer chip is used in between to provide high impedance inputs that do not interfere with the logic being analyzed.

Continue reading World’s Simplest Logic Analyzer for $5

Logic analysis with Bus Pirate

While preparing for my SD tutorial, I realized it would be a long, uphill battle to debug SPI communications with a two-channel oscilloscope, especially when I had no prior experience on implementing SPI with AVR. To break the learning curve to manageable steps, I decided to get a Bus Pirate, a serial protocol tool I had heard a lot of good things about. What made the decision even easier was the fact that my local electronics supplier had just started selling the SparkFun version of Bus Pirate.

In this compact post, I’ll discuss my first impressions of the Bus Pirate, and try out the logic analyzer functionality.

Bus Pirate General Impressions

The first thought that crossed my mind when I saw the Bus Pirate in real life was how small the device was. As you can see, it’s hardly larger than an SD card. All the components are of surface mount type, LEDs included. USB cable was not included but fortunately I had several in my cable drawer. The thing does not need any other setup than plugging it in and installing the FTDI virtual COM port drivers. After that, it showed up as COM19 and I could connect to it with Putty. See the Bus Pirate 101 tutorial for installation details.

The v3 hardware is based on a PIC chip running at 3.3 volts and it took me a while to get comfortable with the power supply & pullup resistor logic – basically you can either use the Bus Pirate pins “normally” so an output pin is driven by the PIC, or in “open drain” mode, where a CD4066B analog switch connects the lines via pullup resistors to whatever is wired to the Vpu pin. This way, the Bus Pirate can interface with other than 3.3V devices (the PIC only pulls the line down or “lets it go” and the pullup takes the line high).
Continue reading Logic analysis with Bus Pirate